Covers & Accessories
The Best Meat Claws and Shredders
A ten-dollar tool that turns the worst ten minutes of a pulled pork cook into the easiest.
By Mike M. · Last updated November 13, 2026 · How we pick
Best Meat Claws

Bear Paws Meat Claws
Bear Paws · Shredding pork shoulder without burning your hands
The original, made in the USA, and the pair every other set is copying.
Price as of November 18, 2026. #ad how this is funded
Quick picks
Prices are live from Amazon as of November 18, 2026 — tap a price to check it now.
| # | Product | Best for | Price |
|---|---|---|---|
| 1 | ![]() Bear Paws Meat Claws Bear Paws The original, made in the USA, and the pair every other set is copying. | Shredding pork shoulder without burning your hands | $13.99Amazon |
| 2 | ![]() Stainless Meat Shredder Claws ZenithShine Steel tines go through a shoulder faster than plastic, for under ten dollars. | Faster shredding, at a lower price | $9.99Amazon |
#ad We earn a commission on purchases made through these links, at no extra cost to you. It never changes the ranking — here is the method.
Bear Paws if you want the stiff plastic original that also lifts a whole shoulder off the grate. Stainless claws if you want to shred faster and spend less. Most people who cook pulled pork regularly end up with both.
They are a lifting tool as much as a shredding tool
The underrated job: getting a nine-pound pork butt off a hot grate and into a pan without it falling apart or burning your forearms. Two forks will not do it. A pair of stiff claws slides underneath and takes the whole thing in one movement, which is the moment most people decide the purchase was worth it.
Plastic or stainless
| Hard plastic | Stainless steel | |
|---|---|---|
| Shredding speed | Slower | Faster — tines cut rather than tear |
| Lifting a whole butt | Better — broader, stiffer | Workable but narrower |
| Non-stick and enamel | Safe | Will scratch |
| Heat | Will scorch on a hot grate | Unaffected |
| Typical price | Around $14 | Under $10 |
Wear gloves underneath. Claws keep your hands out of the meat, not out of the heat — a pork butt straight off the grill at 203°F will burn you through a moment of contact. Nitrile under a cotton liner is the standard combination, covered on our BBQ gloves page.
Rest first, then shred
Shredding a pork butt straight off the grill wastes the juice and scalds your hands. Rest it wrapped for at least an hour first — it will still be far too hot to handle bare-handed, and the meat will have reabsorbed what would otherwise have run onto the board. Full method on our pulled pork page.
What else they are good for
Shredding chicken for tacos, pulling a smoked chuck roast apart, and tossing shredded meat through its own juices without compacting it the way a spoon does. They are also the easiest way to mix bark pieces back through a batch so every portion gets some.
The picks in full
#1 · Shredding pork shoulder without burning your hands
Bear Paws Meat Claws
Bear Paws

The original, made in the USA, and the pair every other set is copying.
- USA made
- Hard plastic, dishwasher safe
- Also lifts a whole shoulder off the grate
Price as of November 18, 2026. #ad how this is funded
Good
- Stiff enough to lift a 9 lb butt, not just shred it
- No metal to scratch a non-stick surface
Trade-off
- Bulky to store
- Plastic will scorch if left on a hot grate
#2 · Faster shredding, at a lower price
Stainless Meat Shredder Claws
ZenithShine

Steel tines go through a shoulder faster than plastic, for under ten dollars.
- Stainless steel tines
- Dishwasher safe
- For pulled pork and chicken
Price as of November 18, 2026. #ad how this is funded
Good
- Cuts through connective tissue faster than plastic
- Cheap enough to own alongside a plastic pair
Trade-off
- Will scratch non-stick and enamel surfaces
- Sharp — not a tool to hand a child
Questions people actually ask
Are meat claws worth it?
For anyone who cooks pulled pork or shredded chicken, yes — they cost under fifteen dollars and they do a job two forks genuinely cannot, which is lifting a whole hot shoulder off the grate in one piece.
Plastic or metal meat claws?
Plastic is stiffer and broader, which makes it better for lifting and safe on non-stick. Metal tines shred faster and cost less. If you only buy one pair, plastic is the more versatile.
Can you put meat claws in the dishwasher?
Both picks here state they are dishwasher safe. Keep plastic claws off a hot grate though — they will scorch.
Sources
Read next
Recipes
Pellet Grill Pulled Pork
225°F, wrap at 165°F, 203°F probe-tender. Hard to get wrong.
Covers & Accessories
The Best BBQ Gloves
Heat-resistant vs nitrile, and why you wear them together.
Covers & Accessories
The Pellet Grill Accessories Worth Buying
Ten accessories ranked by improvement per dollar.
Recipes
Smoked Chuck Roast
250°F, wrap at 165°F, cook to 203°F. Brisket texture, less risk.
Brands: want your product tested? For Brands.